Tele2box
Platform
It is based on a Infineon Danube SoC.
Pictures
OpenWRT
iThe ARV4510 seems to be supported by OpenWRT, but there seems to be a need to flash the bootloader with uBoot.
Screenlog
# ls
antispam dev home mnt proc sys var
bin etc lib opt sbin tmp
# reboot
# The system is going down NOW !!
Sending SIGTERM to all processes.
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
ROM VER: 1.0.3
CFG 01
Read EEPROMX
_
| |__ _____ ____ _ _ __
| '_ \ / _ \ \ /\ / / _` | '_ \
| |_) | __/\ V V / (_| | | | |
|_.__/ \___| \_/\_/ \__,_|_| |_|
Portions Copyright (c) 2005-2007 bewan systems
www.bewan.com
Parameters:
Product : A50801
Product family : A50800
Flash size : 1000000
DRAM size : 2000000
Ethernet : MII
LAN MAC address : 00:0c:c3:71:38:5d
WAN MAC address : 00:0c:c3:71:38:5d
Dual bank boot : yes
Reset : no
Pairing : no
Serial number : 970000074199973
WEP key : 9AYRGS2YA4TNR
Loader version : 8029
Capabilities : 80000000
Found valid bootable partition 0:
Copyright (c) 2006-2007 BeWAN Systems
Arcadyan ARV4510PW-A-LF-L3 - OOL
A50802
2007-07-02-12:27:05
A50802-ool13-6548.bin
Found valid bootable partition 1:
Copyright (c) 2006-2007 BeWAN Systems
Arcadyan ARV4510PW-A-LF-L3 Generic
A50801
2007-10-05-17:54:27
A50801-gen7-8029.bin
Booting from partition 1 in flash.
Loading: Linux Kernel Image
Load address = 80000000
Uncompressing Linux...................
done, booting the kernel.
start addr = 802B1000
memsize=31
TODO: chip version
Linux version 2.6.16bewan (build@megabob) (gcc version 3.3.4) #1 Fri Oct 5 17:41:51 CEST 2007
Reserving memory for CP1 @0xa1f00000
memsize=31
CPU revision is: 00019641
PCI: Probing PCI hardware on host bus 0.
Board with an external oscillator
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: nofpu console=ttyS0,115200n1 bewan_boot=flash1 bewan_fs_addr=0x8e9000 bewan_fs_size=0x717000 mem=31M
Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 128 (order: 7, 2048 bytes)
mips_hpt_frequency:166666667
r4k_offset: 00196e6a(1666666)
Using 166.667 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 27912k/31744k available (2293k kernel code, 3832k reserved, 459k data, 152k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
DANUBE MIPS24KEc MPS mailbox driver, Version 1.1.0
(c) Copyright 2006, Infineon Technologies AG
IFX_MPS: using proc fs
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Squashfs 2.2 with LZMA support
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
io scheduler noop registered (default)
Danube MEI version:1.00.09
Danube MEI MIB version:0.90.04
Danube Port Settings
Danube Port Initialization
cgu: misc_register on minor = 63
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 62
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
ttyS0 at MMIO 0xbe100c00 (irq = 9) is a DANUBEASC
ttyS1 at MMIO 0xbe100400 (irq = 2) is a DANUBEASC
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
danube ETOP driver loaded!
ppe: ATM init succeeded (firmware version 1.1.0.2.1.13
Danube IAD flash device: 0x1000000 at 0xb0000000
Danube IAD FLASH: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "Danube IAD FLASH":
0x00000000-0x01000000 : "Flash"
0x00000000-0x00020000 : "Loader"
0x00020000-0x00040000 : "Config"
0x00820000-0x01000000 : "Firmware"
0x00040000-0x00820000 : "OldFirmware"
bootpart=2
Creating 1 MTD partitions on "Danube IAD FLASH":
0x008e9000-0x01000000 : "romFS"
rootdev = 31,5
LED and Buttons driver: v2.6.0
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
ip_conntrack version 2.4 (248 buckets, 1984 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Ethernet Multiplexer Support v1.0 Christophe Piel (c) 2006 BeWAN systems
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory
DS max rate = 0 kbps
US max rate = 0 kbps
DS payload rate = 0 kbps
US payload rate = 0 kbps
Local CRC = 0
Remote CRC = 0
init started: BusyBox v1.00 (2007.10.05-15:44+0000) multi-call binary
Starting pid 120, console /dev/tts/0: '/etc/rc'
Algorithmics/MIPS FPU Emulator v1.5
Software Watchdog Timer: 0.05, timer margin: 120 sec.
Mon Jan 1 00:00:00 UTC 2007
_
| |__ _____ ____ _ _ __
| '_ \ / _ \ \ /\ / / _` | '_ \
| |_) | __/\ V V / (_| | | | |
|_.__/ \___| \_/\_/ \__,_|_| |_|
IFX TAPI, version 3.5.2.5, (c) 2007 Infineon Technologies
IFX VMMC device driver, version 1.1.6.5, (c) 2007 Infineon Technologies AG
<6>usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
PCI: Enabling device 0000:00:0f.2 (0000 -> 0002)
plat_dev_init(810a6400)
ehci_hcd 0000:00:0f.2: EHCI Host Controller
ehci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0f.2: irq 26, io mem 0x18010000
ehci_hcd 0000:00:0f.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:00:0f.0 (0000 -> 0001)
plat_dev_init(810a6c00)
uhci_hcd 0000:00:0f.0: UHCI Host Controller
uhci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:0f.0: irq 26, io base 0x1ae00000
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
plat_dev_init(810a6800)
uhci_hcd 0000:00:0f.1: UHCI Host Controller
uhci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:0f.1: irq 26, io base 0x1ae00020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
x10: X10 DEV module v2.1.3 (wsh@sprintmail.com)
x10: $Id: dev.c,v 1.22 2005/03/27 04:39:26 root Exp root $
x10: X10 driver successfully loaded
Linux video capture interface: v1.00
pwc: Philips webcam module version 10.0.12-rc1 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usbcore: registered new driver Philips webcam
usbcore: registered new driver quickcam
Vendor: Generic Model: USB Flash Drive Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2072064 512-byte hdwr sectors (1061 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 2072064 512-byte hdwr sectors (1061 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1
sd 0:0:0:0: Attached scsi removable disk sda
/etc/init.d/syslog start
/etc/init.d/dsl start
modprobe: module ctlmeth not found.
modprobe: failed to load module ctlmeth
/etc/init.d/interface start LANEthernetInterface 1
/etc/init.d/switch stop 1
/etc/init.d/phy stop 1 1
using the specified MII index 19.
power down...
/etc/init.d/phy stop 1 2
using the specified MII index 18.
power down...
/etc/init.d/phy stop 1 3
using the specified MII index 17.
power down...
/etc/init.d/phy stop 1 4
using the specified MII index 16.
power down...
/etc/init.d/wifi nothing 1
/etc/init.d/wifi nothing 2
modprobe: module ctlmatm not found.
modprobe: failed to load module ctlmatm
/etc/init.d/interface start ATMEthernetInterface 1
/etc/init.d/atm start 1
/bin/atmcfg atm1 -flowset 15 0 0 3 0 0 0 1
/bin/atmcfg atm1 -vccopen 8 35 15 llc pppoe
/etc/init.d/interface nothing ATMEthernetInterface 2
/etc/init.d/interface nothing ATMEthernetInterface 3
/etc/init.d/interface nothing ATMEthernetInterface 4
/etc/init.d/interface nothing ATMEthernetInterface 5
/etc/init.d/autodslam start auto-stop
/etc/init.d/lan start 1
/etc/init.d/lanif start 1 all
date: 13, month: 7, hour: 58, minute: 4
/etc/init.d/lanintf start lan1 eth0
device eth0 entered promiscuous mode
/etc/init.d/lanintf nothing lan1 ath0
/etc/init.d/lanip start 1
/etc/config.default/ip-up-dhcp lan1 192.168.1.1
lan1: port 1(eth0) entering listening state
/etc/init.d/host start
/etc/init.d/igmp start
/etc/init.d/ipsec restart all
/etc/init.d/landhcp start 1
/etc/init.d/racoon stop
/etc/init.d/lanacl start 1
/etc/init.d/passthrough nothing 1
/etc/init.d/lan nothing 2
/etc/init.d/lan nothing 3
/etc/init.d/lan nothing 4
/etc/init.d/lan nothing 5
/etc/init.d/users start
/etc/init.d/unix start
/etc/init.d/unixusers start 1
/etc/init.d/unixusers start 2
/etc/init.d/samba start
/etc/init.d/pureftpd start
/etc/init.d/unixadmin start
/etc/init.d/time start
/etc/init.d/mdns start
/etc/init.d/rmthttp start
/etc/init.d/wan start 1
/etc/init.d/interface start WANConnectionDevice 1
/etc/init.d/wannet start 1
/etc/init.d/wanbr nothing 1
/etc/init.d/wanip nothing 1
/etc/init.d/wanppp start 1
/etc/init.d/firewall start 1
/etc/init.d/ports start 1
/etc/init.d/wan nothing 2
/etc/init.d/wan nothing 3
/etc/init.d/wan nothing 4
/etc/init.d/wan nothing 5
/etc/init.d/qos start all
/etc/init.d/dhcp start all
/etc/init.d/dhcpd start all
/etc/init.d/dhcrelay start all
/etc/init.d/hbrdhcp start all
/etc/init.d/dnsmasq start all
/etc/init.d/pppd start all
/etc/init.d/dhclient start all
/etc/init.d/hostapd nothing all
/etc/init.d/wsccmd nothing all
/etc/init.d/wpa_supplicant nothing all
/etc/init.d/pptp stop
/etc/init.d/openl2tp stop
/etc/init.d/ipsec restart all
/etc/init.d/racoon stop
lan1: port 1(eth0) entering learning state
/etc/init.d/fwrules nothing
/etc/init.d/iptables start
/etc/init.d/ebtables nothing
/etc/init.d/routes start
/etc/init.d/upnp start
/etc/init.d/dyndns nothing
/etc/init.d/phy start 1 1
using the specified MII index 19.
resetting the transceiver...
restarting autonegotiation...
/etc/init.d/phy start 1 2
using the specified MII index 18.
resetting the transceiver...
restarting autonegotiation...
/etc/init.d/phy start 1 3
using the specified MII index 17.
resetting the transceiver...
restarting autonegotiation...
/etc/init.d/phy start 1 4
using the specified MII index 16.
resetting the transceiver...
restarting autonegotiation...
modprobe: module fuse not found.
modprobe: failed to load module fuse
/etc/init.d/inittab
rc completed
Starting pid 969, console /dev/tts/0: '/bin/sh'
# Starting pid 970, console /dev/null: '/sbin/syslogd'
Starting pid 971, console /dev/null: '/sbin/klogd'
Starting pid 972, console /dev/null: '/bin/dhcpd'
Starting pid 973, console /dev/null: '/bin/dnsmasq'
Starting pid 974, console /dev/null: '/sbin/igmpproxyd'
Starting pid 975, console /dev/null: '/bin/mDNSResponderPosix'
Starting pid 976, console /dev/null: '/bin/pppd'
Starting pid 977, console /dev/console: '/bin/resetd'
Starting pid 979, console /dev/console: '/bin/wdgd'
Starting pid 978, console /dev/null: '/bin/upnpd'
Software Watchdog Timer: set margin to 40 sec.
/etc/init.d/upgd nothing
/etc/init.d/inetd start
/etc/init.d/http start
/etc/init.d/htpwd start
/etc/init.d/tr069 nothing
/etc/init.d/usbdevices
/etc/init.d/printer start
/etc/init.d/voip-asterisk nothing
/etc/init.d/bluetooth nothing
/etc/init.d/host start
lan1: topology change detected, propagating
lan1: port 1(eth0) entering forwarding state
/etc/init.d/userscreatedir start
/etc/init.d/usersdir start 1
/etc/init.d/usersdir start 2
/etc/init.d/sambaserver refresh
/etc/init.d/pureftpdserver start
/etc/init.d/obexpush nothing4
/etc/init.d/upnpav nothing
/etc/init.d/web nothing
/etc/init.d/webcam start
/etc/init.d/inittab
Reloading /etc/inittab
Starting pid 1316, console /dev/console: '/bin/thttpd'
Starting pid 1317, console /dev/null: '/bin/vidcat'
# ls
antispam dev home mnt proc sys var
bin etc lib opt sbin tmp
# cat /et
# cd /etc
# lks
-sh: lks: not found
# ls
asterisk dsskey.bin lighttpd rc
asterisk.default file motd rc2
bluetooth flash p3scan release
chatscripts fstab passwd resolv.conf
codepages group ppp services
config hosts ppp.default version
config.default inetd.conf pptpd
dhclient-script init.d pptpd.default
dhcpd-up inittab ramfs.img
# cd /lib
# ls
asterisk libm-0.9.27.so libsamba.so.0
configlib.so libm.so.0 libssl.so
iptables libmagic.so libssl.so.0
ld-uClibc-0.9.27.so libmagic.so.1 libssl.so.0.9.8
ld-uClibc.so.0 libmagic.so.1.0.0 libuClibc-0.9.27.so
libadm6996.so libnetlink.so libusb-0.1.10a.so
libc.so.0 libnsl-0.9.27.so libusb.so
libcrypt-0.9.27.so libnsl.so.0 libusb.so.0
libcrypt.so.0 libplat.so libutil-0.9.27.so
libcrypto.so libpng.so libutil.so.0
libcrypto.so.0 libpng.so.0 libz.so
libcrypto.so.0.9.8 libpng.so.0.1.2.8 libz.so.1
libdhcp.so libpthread-0.9.27.so libz.so.1.2.3
libdl-0.9.27.so libpthread.so.0 mod_auth.so
libdl.so.0 libresolv-0.9.27.so mod_cgi.so
libiputil.so libresolv.so.0 mod_dirlisting.so
libiw.so.27 librt-0.9.27.so mod_indexfile.so
libjpeg.so librt.so.0 mod_staticfile.so
libjpeg.so.62 libsamba-0.1.0.so modules
libjpeg.so.62.0.0 libsamba.so rp-pppoe.so
# cd
cd asterisk
# ls
modules
# cd mi
odules
# ls
app_dial.so chan_mgcp_ua.so format_g723.so format_wav.so
app_echo.so chan_phone_tapi.so format_g726.so format_wav_gsm.so
app_playback.so chan_sip.so format_g729.so func_callerid.so
app_system.so codec_alaw.so format_gsm.so pbx_config.so
app_while.so codec_gsm.so format_pcm.so res_features.so
chan_local.so codec_ulaw.so format_pcm_alaw.so res_indications.so
# cd .
cd ../
# ls
modules
# cd ..
# ls
asterisk libm-0.9.27.so libsamba.so.0
configlib.so libm.so.0 libssl.so
iptables libmagic.so libssl.so.0
ld-uClibc-0.9.27.so libmagic.so.1 libssl.so.0.9.8
ld-uClibc.so.0 libmagic.so.1.0.0 libuClibc-0.9.27.so
libadm6996.so libnetlink.so libusb-0.1.10a.so
libc.so.0 libnsl-0.9.27.so libusb.so
libcrypt-0.9.27.so libnsl.so.0 libusb.so.0
libcrypt.so.0 libplat.so libutil-0.9.27.so
libcrypto.so libpng.so libutil.so.0
libcrypto.so.0 libpng.so.0 libz.so
libcrypto.so.0.9.8 libpng.so.0.1.2.8 libz.so.1
libdhcp.so libpthread-0.9.27.so libz.so.1.2.3
libdl-0.9.27.so libpthread.so.0 mod_auth.so
libdl.so.0 libresolv-0.9.27.so mod_cgi.so
libiputil.so libresolv.so.0 mod_dirlisting.so
libiw.so.27 librt-0.9.27.so mod_indexfile.so
libjpeg.so librt.so.0 mod_staticfile.so
libjpeg.so.62 libsamba-0.1.0.so modules
libjpeg.so.62.0.0 libsamba.so rp-pppoe.so
# cd //
# ls
antispam dev home mnt proc sys var
bin etc lib opt sbin tmp
# cd home
# ls
# ps
PID Uid VmSize Stat Command
1 root 360 S init
2 root SW< [ksoftirqd/0]
3 root SW< [events/0]
4 root SW< [khelper]
5 root SW< [kthread]
6 root SW< [kblockd/0]
39 root SW [pdflush]
40 root SW [pdflush]
42 root SW< [aio/0]
41 root SW [kswapd0]
47 root SW [kmibpoll]
48 root SW [dsl/0]
80 root SW< [eth_leds]
95 root SW [mtdblockd]
210 root SW< [khubd]
318 root SW< [scsi_eh_0]
319 root SW< [usb-storage]
508 root 316 S /sbin/danube_autoboot_daemon /sbin/modemhwe.bin all
969 root 360 S -sh
970 root 328 S /sbin/syslogd -n -S -C 64
971 root 308 S /sbin/klogd -n
972 root 436 S /bin/dhcpd -q -d -f -cf /etc/config/dhcpd.conf -lf /v
973 root 320 S /bin/dnsmasq -f -r /var/etc/config/resolv.conf -l /va
974 root 364 S /sbin/igmpproxyd -D -l3 -c /var/etc/config/igmpproxy.
975 root 388 S /bin/mDNSResponderPosix -f /etc/config/mdns/services.
976 root 584 S /bin/pppd file /etc/ppp/options.wan1 wan1
977 root 280 S /bin/resetd
978 root 680 S /bin/upnpd lan1 ppp1
979 root 156 S /bin/wdgd
991 root 680 S /bin/upnpd lan1 ppp1
992 root 680 S /bin/upnpd lan1 ppp1
993 root 680 S /bin/upnpd lan1 ppp1
994 root 680 S /bin/upnpd lan1 ppp1
995 root 680 S /bin/upnpd lan1 ppp1
996 root 680 S /bin/upnpd lan1 ppp1
997 root 680 S /bin/upnpd lan1 ppp1
998 root 680 S /bin/upnpd lan1 ppp1
999 root 680 S /bin/upnpd lan1 ppp1
1316 root 356 S /bin/thttpd -p 8080 -d /etc/config.default/html -i /v
1317 root 336 S /bin/vidcat -d /dev/v4l/video0 -o /var/home/www/webca
1329 root 348 R ps
# Process '-/bin/sh' (pid 969) exited. Scheduling it for restart.
usb 1-1: USB disconnect, address 2
/etc/init.d/pureftpdserver stop
/etc/init.d/obexpush stop
/etc/init.d/upnpav stop
/etc/init.d/web stop
/etc/init.d/inittab
Reloading /etc/inittab
/etc/init.d/userscreatedir start
/etc/init.d/usersdir start 1
/etc/init.d/usersdir start 2
/etc/init.d/sambaserver refresh
/etc/init.d/pureftpdserver start
/etc/init.d/obexpush nothing4
/etc/init.d/upnpav nothing
/etc/init.d/web nothing
/etc/init.d/inittab
Reloading /etc/inittab