Sitecom WL153

Pictures

Serial Port

RX GND TX VCC

Only connecting RX GND TX was enough to get the serial access.

Log

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2009.12.06 18:36:12 =~=~=~=~=~=~=~=~=~=~=~=
+Ethernet eth0: MAC address 00:50:fc:02:03:04
IP: 192.168.12.142/255.255.240.0, Gateway: 192.168.12.14
Default server: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 21:05:24, Oct 17 2005

Platform: PC (I386) 
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.R1

RAM: 0x00000000-0x000f0000, 0x00070470-0x000a0000 available
linux -b 0x400000 -l 0x0009be0c -s 0x00142a3d -c "console=ttyS0,38400"
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> IP: 192.168.12.142/255.255.240.0, Gateway: 192.168.12.14
Default server: 192.168.12.148
RedBoot> 
mem_size: 1000000
initrd e9d000 len 142a3d
Linux version 2.4.25-386 (root@Fedora) (gcc version 3.3.1) #1445 Tue Jul 25 15:19:38 CST 2006
BIOS-provided physical RAM map:
 BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e801: 0000000000100000 - 0000000001000000 (usable)
16MB LOWMEM available.
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
DMI not present.
Kernel command line: console=ttyS0,38400
No local APIC present or hardware disabled
Initializing CPU#0
Calibrating delay loop... 50.79 BogoMIPS
Memory: 13060k/16384k available (950k kernel code, 2936k reserved, 221k data, 84k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
CPU: Cyrix Cx486SLC
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: none
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LED & GPIO & LAN Status Driver LED_VERSION 
IA-32 Microcode Update Driver: v1.13 <tigran@veritas.com>
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
HDLC line discipline: version $Revision: 3.7 $, maxframe=4096
N_HDLC line discipline registered.
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
r6040: RDC R6040 net driver, version 0.8 (28March2005)
r6040: RDC R6040 net driver, version 0.8 (28March2005)
r6040: RDC R6040 net driver, version 0.8 (28March2005)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MX29LV320B flash device: 200000 at ffe00000
 Amd/Fujitsu Extended Query Table v1.0 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 1 MTD partitions on "MX29LV320B flash device":
0x00000000-0x001f0000 : "Flash Disk 1"
MX29LV320B flash device initialized
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.2.3: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
aaaaaaaaaaa
bbbbbbbbbbb
RAMDISK: Compressed image found at block 0
Uncompressing....... <5>done 
Freeing initrd memory: 1290k freed
VFS: Mounted root (ext2 filesystem).
dddddddddd
Freeing unused kernel memory: 84k freed
run_init_process:/sbin/init, env PATH=/bin:/usr/bin:/sbin
insmod: islpc

Please press Enter to activate this console. Sat Jan  1 00:00:00 UTC 2000
 R6040 phyAddr=5, Link at Full duplex
 R6040 phyAddr=4, Link at Full duplex
killall: pptp.sh: no process killed

killall: pppoe.sh: no process killed
Initialize WLAN interface
Using /bin/rt61ap.o
*RT61*<7>===> RT61_init_one
*RT61*<7>Driver version-1.0.6.0
*RT61*<7>ra0: at 0xd5000000, VA 0xc1a52000, IRQ 12. 
*RT61*<7><=== RT61_init_one
*RT61*<7>===> NICLoadFirmware
*RT61*<7>NICLoadFirmware: CRC ok, ver=1.0
*RT61*<7><=== NICLoadFirmware (src=/etc/Wireless/RT61AP/RT2661.bin, status=0)
*RT61*<7>--> RTMPAllocAdapterBlock
*RT61*<7><-- RTMPAllocAdapterBlock
*RT61*<7>--> RTMPAllocDMAMemory
*RT61*<7>TxRing[0]: total 96 entry allocated
*RT61*<7>TxRing[1]: total 96 entry allocated
*RT61*<7>TxRing[2]: total 96 entry allocated
*RT61*<7>TxRing[3]: total 96 entry allocated
*RT61*<7>TxRing[4]: total 96 entry allocated
*RT61*<7>MGMT Ring: total 32 entry allocated
*RT61*<7>Rx Ring: total 96 entry allocated
*RT61*<7><-- RTMPAllocDMAMemory
*RT61*<7><--> NICInitTxRxRingAndBacklogQueue
*RT61*<7>--> MLME Initialize
*RT61*<7><-- MLME Initialize
*RT61*<7>--> PortCfgInit
*RT61*<7><-- PortCfgInit
*RT61*<7>--> NICInitializeAdapter
*RT61*<7>--> NICInitializeAsic
*RT61*<7>BBP version = 48
*RT61*<7><-- NICInitializeAsic
*RT61*<7><-- NICInitializeAdapter
*RT61*<7>CountryRegion=5
*RT61*<7>SSID[0]=Sitecom
*RT61*<7>PhyMode=1
*RT61*<7>I/F(ra0) TxRate=(16,00,00,00,00,00,00,00,00,00,00,00)
*RT61*<7>Channel=1
*RT61*<7>BasicRate=3
*RT61*<7>BeaconPeriod=100
*RT61*<7>DtimPeriod=3
*RT61*<7>TxPower=100
*RT61*<7>BGProtection=2
*RT61*<7>OLBCDetection=0
*RT61*<7>TxAntenna=-1
*RT61*<7>RxAntenna=
*RT61*<7>TxPreamble=0
*RT61*<7>RTSThreshold=2347
*RT61*<7>FragThreshold=2346
*RT61*<7>TxBurst=0
*RT61*<7>PktAggregate=1
*RT61*<7>TurboRate=1
*RT61*<7>I/F(ra0) WmmCapable=1
*RT61*<7>I/F(ra0) NoForwarding=0
*RT61*<7>NoForwardingBTNBSSID=0
*RT61*<7>I/F(ra0) HideSSID=0
*RT61*<7>ShortSlot=1
*RT61*<7>AutoChannelAtBootup=0
*RT61*<7>IEEE8021X=0
*RT61*<7>IEEE80211H=0
*RT61*<7>CSPeriod=10
*RT61*<7>I/F(ra0) AuthMode=2
*RT61*<7>I/F(ra0) EncrypType=0
*RT61*<7>ReKeyMethod=2
*RT61*<7>PMKCachePeriod=60000
*RT61*<7>I/F(ra0) DefaultKeyID(0~3)=0
*RT61*<7>I/F(ra0) Key1Str=1674ae0cb1814e95bcfc44263d and type=Hex
*RT61*<7>I/F(ra0) Key2Str=00000000000000000000000000 and type=Hex
*RT61*<7>I/F(ra0) Key3Str=00000000000000000000000000 and type=Hex
*RT61*<7>I/F(ra0) Key4Str=00000000000000000000000000 and type=Hex
*RT61*<7>HSCounter=0
*RT61*<7>AccessPolicy0=0
*RT61*<7>WDS-Enable mode=0
*RT61*<7>WDS-AP(00) (0)-00:00:00:00:00:00
*RT61*<7>WDS-AP(01) (0)-00:00:00:00:00:00
*RT61*<7>WDS-AP(02) (0)-00:00:00:00:00:00
*RT61*<7>WDS-AP(03) (0)-00:00:00:00:00:00
*RT61*<7>--> NICReadEEPROMParameters
*RT61*<7>MBSSID[0] MAC=00:0c:f6:23:9f:53
*RT61*<7>E2PROM: Version = 1, FAE release #0
*RT61*<7>E2PROM: G Tssi[-4 .. +4] = 255 255 255 255 - 255 -255 255 255 255, step=255, tuning=0
*RT61*<7>E2PROM: A Tssi[-4 .. +4] = 255 255 255 255 - 255 -255 255 255 255, step=255, tuning=0
*RT61*<7>E2PROM: RF freq offset=0x1c, RF programming seq=0
*RT61*<7>TxPowerDelta Config (Delta=0, Sign=0, Enable=0)
*RT61*<7><-- NICReadEEPROMParameters
*RT61*<7>country code=5/0, RFIC=1, PHY mode=1, support 14 channels
*RT61*<7>channel #1
*RT61*<7>channel #2
*RT61*<7>channel #3
*RT61*<7>channel #4
*RT61*<7>channel #5
*RT61*<7>channel #6
*RT61*<7>channel #7
*RT61*<7>channel #8
*RT61*<7>channel #9
*RT61*<7>channel #10
*RT61*<7>channel #11
*RT61*<7>channel #12
*RT61*<7>channel #13
*RT61*<7>channel #14
*RT61*<7>IF(ra0) RTMPSetPhyMode(=1)
*RT61*<7>I/F(ra0) TxRate=(16,00,00,00,00,00,00,00,00,00,00,00)
*RT61*<7>--> NICInitAsicFromEEPROM
*RT61*<7>RFIC=4, LED mode=0
*RT61*<7><-- NICInitAsicFromEEPROM
*RT61*<7>Register WDS(virtual) interface(ra1)-00:00:00:00:00:00
*RT61*<7>Register WDS(virtual) interface(ra2)-00:00:00:00:00:00
*RT61*<7>Register WDS(virtual) interface(ra3)-00:00:00:00:00:00
*RT61*<7>Register WDS(virtual) interface(ra4)-00:00:00:00:00:00
*RT61*<7>---> ApInitialize
*RT61*<7><--- ApInitialize
*RT61*<7>---> ApStartUp
*RT61*<7>IF(ra0) CapabilityInfo=11, WepStatus=0
*RT61*<7>IF(ra0)-AP AuthMode=2, disable Pairwise Key Table
*RT61*<7>AsicRemoveSharedKeyEntry: #0 
*RT61*<7>AsicRemoveSharedKeyEntry: #1 
*RT61*<7>AsicRemoveSharedKeyEntry: #2 
*RT61*<7>AsicRemoveSharedKeyEntry: #3 
*RT61*<7>AsicAddSharedKeyEntry(BssIndex=0): wep128 key #0
*RT61*<7>     Key =16:74:ae:0c:b1:81:4e:95:bc:fc:44:26:3d:00:00:00:
*RT61*<7>AsicAddSharedKeyEntry(BssIndex=0): wep128 key #1
*RT61*<7>     Key =00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:
*RT61*<7>AsicAddSharedKeyEntry(BssIndex=0): wep128 key #2
*RT61*<7>RSSI=-121, CCA=0, --R17= 0x3f, R62=4 
*RT61*<7>     Key =00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:
*RT61*<7>AsicAddSharedKeyEntry(BssIndex=0): wep128 key #3
*RT61*<7>     Key =00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:
*RT61*<7>AsicSetEdcaParm
*RT61*<7>AP [Cnt#0]: AIFSN CWmin CWmax TXOP(us)  ACM
*RT61*<7>    AC_BE     0     0     0        0     0
*RT61*<7>    AC_BK     0     0     0        0     0
*RT61*<7>    AC_VI     0     0     0        0     0
*RT61*<7>    AC_VO     0     0     0        0     0
*RT61*<7>STA        : AIFSN CWmin CWmax TXOP(us)  ACM
*RT61*<7>    AC_BE     0     0   0       0     0
*RT61*<7>    AC_BK     0     0   0       0     0
*RT61*<7>    AC_VI     0     0     0       0     0
*RT61*<7>    AC_VO     0     0     0        0     0
*RT61*<7>AsicSwitchChannel(RF=4, Pwr=5) to #1, R1=0x95002ccc, R2=0x95004786, R3=0x95068a55, R4=0x950dca0b
*RT61*<7>UpdateBasicRateBitmap::(BasicRateBitMap=3)(82,84,0b,16,00,00,00,00,00,00,00,00)
*RT61*<7>IF(ra0) MlmeUpdateTxRates (MaxDesire=11 Mbps, MaxSupport=11 Mbps, MaxTxRate=11 Mbps, Rate Switching =0)
*RT61*<7> MlmeUpdateTxRates (RtsRate=11 Mbps, MlmeRate=1 Mbps, BasicRateBitmap=0x0003)
*RT61*<7>MakeBssBeacon(ra0)(FrameLen=80,TimIELocateInBeacon=80,CapInfoLocateInBeacon=34)
*RT61*<7>SW interrupt MCU (cmd=0x60, token=0xff, arg1,arg0=0x00,0x00)
*RT61*<7>--->AsicEnableBssSync(INFRA mode)
*RT61*<7>--->Disable TSF synchronization
*RT61*<7>LOG#0 00:0c:f6:23:9f:53 restart access point
*RT61*<7><--- ApStartUp (sec_csr4=0x0)
*RT61*<7>==> Set_Debug_Proc *******************
Setup BRIDGE interface

SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
 R6040 phyAddr=5, Link at Full duplex
SIOCDELRT: No such process

device ra0 entered promiscuous mode
ra0: attempt to add interface with same source address.
SIOCDELRT: No such process

br0: port 2(ra0) entering listening state
br0: port 1(eth0) entering listening state
SIOCDELRT: No such process

SIOCDELRT: No such process
Static DHCP Leases disable!
SIOCDELRT: No such process
udhcpd (v0.9.9-pre) started
max_leases value (254) not sane, setting to 101 instead
Setup WAN interface
br0: port 2(ra0) entering learning state
br0: port 1(eth0) entering learning state
********** run Diagd **********

setting: port: 31727 
running in daemon mode
********** run GaTest **********

rm: cannot remove `/tmp/agentenabledflag': No such file or directory
udhcp client (v0.9.9-pre) started
into eth1.deconfig
-sh: /etc/stupid-ftpd/ftpd: not found
[?3l[2J[20;1H-------------------------------------------------------------------------------[21;1H[7m[21;1H<TAB> Select                     <ESC> Exit                     <Enter> Enter[0m[4;10HPlease enter your Name and Password[8;2H[7mUser Name[0m[8;14H:br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating

Links