Mood300

Serial output

U-Boot 1.1.1 (Jun 22 2005 - 13:29:30)

Board: Mood 300 Series
CPU: Au1550, id: 0x02, rev: 0x00
DRAM:  128 MB
Flash:    2 MB
NAND:  64 MB
Using default environment

No debug adapter present - disabling input

In:    No input devices available!
Out:   serial
Err:   serial
Net:   Au1X00 ETHERNET
Hit any key to stop autoboot:  0

Loading from device 0: NAND 64MiB 3,3V 8-bit at 0xbfb00000 (offset 0x0)
   Image Name:
   Created:     2006-12-14   9:54:46 UTC
   Image Type:     MIPS Linux Kernel Image (gzip compressed)
   Data Size:     3205001 Bytes =  3.1 MB
   Load Address: 80100000
   Entry Point:  802d4040
## Booting image at 81000000 ...
   Image Name:
   Created:     2006-12-14   9:54:46 UTC
   Image Type:     MIPS Linux Kernel Image (gzip compressed)
   Data Size:     3205001 Bytes =  3.1 MB
   Load Address: 80100000
   Entry Point:  802d4040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

CPU revision is: 03030200
Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Linux version 2.4.30 (mar@mar) (gcc version 3.3.6) #1 Thu Dec 14 10:52:32 CET 2006
I3 Micro Technology Mood 300 STB
Au1550 AA (PRId 03030200) @ 324MHZ
BCLK switching enabled!
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initial ramdisk at: 0x80310000 (2342912 bytes)
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram0 rw console=ttyS0,115200 usb_ohci=base:0x14020000,len:0x100000,irq:26
calculating r4koff... 00317040(3240000)
Using 324.000 MHz high precision timer.
Console: colour dummy device 80x25
Calibrating delay loop... 323.58 BogoMIPS
Memory: 121728k/131072k available (1857k kernel code, 9344k reserved, 2408k data, 112k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Autoconfig PCI channel 0x8030f3a8
Scanning bus 00, I/O 0x00000300:0x00100000, Mem 0x40000000:0x50000000
00:05.0 Class 0000: 104c:9065 (rev 01)
    Mem at 0x40000000 [size=0x400000]
    Mem at 0x40800000 [size=0x800000]
    I/O at 0x00000300 [size=0x10]
Non-coherent PCI accesses enabled
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-proc.o version 2.6.1 (20010830)
Serial driver version 1.01 (2001-02-08) with no serial options enabled
ttyS00 at 0xb1100000 (irq = 0) is a 16550
ttyS01 at 0xb1200000 (irq = 8) is a 16550
ttyS02 at 0xb1400000 (irq = 9) is a 16550
AMD Alchemy Au1550 RTC Driver v0.6, initialized.
Au1550 SPI driver
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
au1000eth.c:1.4 ppopov@mvista.com
eth0: Au1x Ethernet found at 0xb0500000, irq 27
ethaddr not set in boot prom
eth0: No mac address found
eth0: Micrel KS8721b/BT 10/100 Base Tx/Fx PHY at phy address 1
ks8721m_init - phy = 1
eth0: Using Micrel KS8721b/BT 10/100 Base Tx/Fx PHY as default
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

hda: probing with STATUS(0x50) instead of ALTSTATUS(0x08)
hda: WDC WD800UE-22HCT0, ATA DISK drive
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xb0)
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xb0)
ide0 at 0xc0174000-0xc0174007,0xc01741c0 on irq 62
hda: attached ide-disk driver.
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, (U)DMA
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
Au1550 psc audio: AC'97 Base/Extended ID = 6d50/0205
physmap flash device: 4000000 at 8000000
Mood 300 flash: probing 16-bit flash bus
ioremap(0x1fc00000, 0x00400000) = 0xbfc00000
Mood 300 flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
Mood 300 flash: JEDEC Device ID is 0xC4. Assuming broken CFI table.
Mood 300 flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 5 MTD partitions on "Mood 300 flash":
0x00000000-0x00050000 : "all"
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "parameters"
0x00040000-0x00050000 : "parameters-sysdef"
0x00050000-0x00200000 : "misc"
yxa: 0xec:0x76
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 2 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00400000 : "Mood 300 NAND FS 0"
0x00400000-0x04000000 : "Mood 300 NAND FS 1"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xb4020000, IRQ 26
host/usb-ohci.c: usb-builtin.OHC, non-PCI OHCI
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: b4020000
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2288k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 112k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.84 booting
Setting hostname to "MH02K546R1A00000375143":done.
SERIAL: MH02K546R1A0-0000375143
MAC: 00:02:61:0d:f2:df
Extracting flash files: done.
|S00sysctl| Setting sysctl parameters: done.
|S05norfs| Mounting NOR flash filesystem:
|S05norfs| done.
Configuring OSS mixer settings: done.
Probing hardware devices:
 >> dm642pci_fxn_probe called
Writing Warm Reset (WARMRESET) to HDCR
enable_irq(1) unbalanced from c017a1b8
Setting PNX8510 video dacs to sleep...
Basic Coff Parser and Loader Example for DM642 EVM
Opening DM642 PCI driver...
The DM642 EVM device was opened successfully.
Loading Program ...
Issuing Run...
Let's wait for the dsp to settle down........
modprobe i3mmbfb system=PAL fb0=720,576,32,0,0 fb1=720,576,8,0,0

 >> PCILINK: Initializing...
 >> PCILINK: Init completed!
mmbfb: Using DSP image version 4.18
mmbfb: Define DSP fb0 720x576+0+0@32
mmbfb: Define DSP fb1 720x576+0+0@8
mmbfb: Setting DSP system = PAL
mmbfb: Initializing framebuffer 0 (of 2)...
mmbfb:     DSP addr: 0x8026a000
mmbfb:     DSP reported size: 720x576x32
mmbfb:     FB uses 1658880 bytes (line length: 2880, xres: 720, yres: 576, available: 1658880)
Console: switching to colour frame buffer device 90x36
mmbfb: Initializing framebuffer 1 (of 2)...
mmbfb:     DSP addr: 0x80204000
mmbfb:     DSP reported size: 720x576x8
mmbfb:     FB uses 414720 bytes (line length: 720, xres: 720, yres: 576, available: 414720)
<managerd>
managerd:main: MANAGERD-> started
ipclib:ipc_init: ipclib-managerd: init IPCLIB 2.0
<fade>
fade:main: Fade daemon started. (c) 2004, i3 micro technology ab
Fade hardware: Philips PNX8510
ipclib:ipc_init: ipclib-fade: init IPCLIB 2.0
|S16hdfs_system|  starting...
Checking if we have a disk
Disk found
ipclib:ipc_send_msg: ipc_send_msg: Can't open FIFO device /dev/playtv.fifo
ipc_send_msg: No such file or directory
ipclib:ipc_send_msg: ipc_send_msg: Can't open FIFO device /dev/playtv.fifo
ipc_send_msg: No such file or directory
Setting spindown time
e2fsck 1.34 (25-Jul-2003)
/dev/hda2: recovering journal
/dev/hda2: clean, 531/131328 files, 21327/262144 blocks
kjournald starting.  Commit interval 2 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
|S16hdfs_system| done
|hdfs_user|  starting...
Checking if disk is available/usable
|hdfs_user| done
Checking if system partition is mounted
user devices:  hda3
FB_TEXTBOX -> Message,

HET ONDERHOUD VAN DE SCHIJF IS BEZIG

GELIEVE  ENKELE   MINUTEN  TE
WACHTEN  TOT  HET  ONDERHOUD
VOLTOOID IS, ZONDER DE BOX UIT EN AAN TE ZETTEN.
e2fsck 1.34 (25-Jul-2003)
/dev/hda3: recovering journal
/dev/hda3: clean, 12/9519104 files, 307173/19013264 blocks
FB_TEXTBOX -> Message,

HET ONDERHOUD VAN DE SCHIJF IS VOLTOOID.
tune2fs 1.34 (25-Jul-2003)
The filesystem already has a journal.
kjournald starting.  Commit interval 2 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Mounted  hda3
|hdfs_user| done
<hdmonitor>
Starting hdmonitor with timeout=60
|hwdetect| using HDD
|nandfs| System partition is harddisk, doing nothing
JKW /media/hdd/AUX
|S21persist| setting persistant storage root to '/media/hdd/AUX/persist/'
|S21persist| done
Bootimage: Showing bootimage: /media/persist/bootimage/boot.bmp.gz
|S40networking| starting...
|bootprogress| *** 250 ***
|S40networking| /etc/init.d/dhcp
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
|S40networking| 1
|S50recon| no network, exiting
|appfs| not configured - aborting!
|getsoftware| started
cat: /tmp/bootmethod: No such file or directory
|getsoftware| getbootmethod
|getsoftware| boot method = recon
|getsoftware| ERROR: filesystems not mounted!
INIT: No network, switching to runlevel 1
INIT: Entering runlevel: 1
cat: /tmp/bootmethod: No such file or directory
|S99background-networking| getbootmethod
retrying in 22 seconds
|S99background-networking| Retrying network configuration
|networking| starting...
|bootprogress| *** 250 ***
|networking| /etc/init.d/dhcp
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
|networking| 1
cat: /tmp/bootmethod: No such file or directory
|S99background-networking| getbootmethod
retrying in 108 seconds
|networking| starting...
|bootprogress| *** 250 ***
|networking| /etc/init.d/dhcp
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
Getting network parameters (DHCP) :
udhcp client (v0.9.8) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing.
|networking| 1
cat: /tmp/bootmethod: No such file or directory
|S99background-networking| getbootmethod
retrying in 558 seconds