Mood Media MP7000

Pictures

here

Serial output

115200

U-Boot 1.1.2 (Jun  7 2005 - 09:16:44)
U-Boot code: C0700000 -> C0718CD0  BSS: -> C071D304
CPU: Cirrus Logic <unknown> (ID 0x9213 - Rev. E0)
RAM Configuration:
Bank #0: c0000000 32 MB
Flash:  4 MB
*** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  1 
## Booting image at 00020000 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    718308 Bytes = 701.5 kB
   Load Address: c0008000
   Entry Point:  c0008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.4.27-vrs1-crus142 (mp7000@DevptMP7000) (gcc version 3.3) #5 ven jun 2 12:22:16 CEST 2006
CPU: Arm920Tid(wb) revision 0
Machine: edb9312
Examining tag list @0xc0000100 ...Ok.
parsing command line... ok.
bootmem_init... ok.
paging_init... On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
requesting resources... ok.
Kernel command line: root=1f02 console=ttyAM0 mtdparts=phys_mapped_flash:128k(Uboot)ro,1024k(kernel)ro,1024k(cramfs)ro,-(jffs2)
Calibrating delay loop... 99.36 BogoMIPS
Before waiting loop for hard drive
After waiting loop for hard drive
Memory: 32MB = 32MB total
Memory: 30676KB available (1311K code, 340K data, 44K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
CPU: Testing write buffer: pass
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
GPIO port C initialised 
GPIO port B initialised 
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
ttyAM0 at MMIO 0xff8c0000 (irq = 52) is a AMBA
ttyAM1 at MMIO 0xff8d0000 (irq = 54) is a AMBA
ttyAM2 at MMIO 0xff8e0000 (irq = 55) is a AMBA
pty: 256 Unix98 ptys configured
ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic
Dma memory allocated : 1164 @ 0xc287e000
ep93xx_ethernet #0 at 0xff010000 IRQ:39 MAC:00:ba:d0:0b:ad:00
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive
hdb: Maxtor 6L080P0, ATA DISK drive
ide0 at 0x800-0x807,0x406 on irq 40
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 160086528 sectors (81964 MB) w/8192KiB Cache, CHS=158816/16/63, UDMA 2 
hda: attached ide-cdrom driver.
hda: ATAPI 40X DVD-ROM drive, 254kB Cache, UDMA 2 
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hdb: hdb1 hdb2
SCSI subsystem driver Revision: 1.00
EDB9312-NOR:0x00800000 at 0x00000000
Unknown command : 0xff
Unknown command : 0xff
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
NOR flash on EDB9312: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
mtd: Giving out device 0 to NOR flash on EDB9312
EDB9312-NOR:using edb9312 partition definition
Creating 3 MTD partitions on "NOR flash on EDB9312":
0x00000000-0x00120000 : "zImage"
mtd: Giving out device 1 to zImage
0x00120000-0x00220000 : "CRAMFS"
mtd: Giving out device 2 to CRAMFS
0x00220000-0x007e0000 : "JFFS2"
mtd: Giving out device 3 to JFFS2
EDB9312-NOR:no partition info available
i2c-core.o: i2c core module version 2.6.1 (20010830)
Initialising first I2C bus
Initialising second I2C bus
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xff020000, IRQ 56
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 44K
init started:  BusyBox v1.00 (2006.06.14-15:05+0000) multi-call binary
Using /modules/mood_screen.o
U-Boot 1.1.2 (Jun  7 2005 - 09:16:44)
U-Boot code: C0700000 -> C0718CD0  BSS: -> C071D304
CPU: Cirrus Logic <unknown> (ID 0x9213 - Rev. E0)
RAM Configuration:
Bank #0: c0000000 32 MB
Flash:  4 MB
*** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  1 
EDB9312> 
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> <INTERRUPT>
EDB9312> help
?       - alias for 'help'
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp    - boot image via network using BootP/TFTP protocol
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
echo    - echo args to console
erase   - erase FLASH memory
flinfo  - print FLASH memory information
fsinfo    - print information about filesystems
fsload    - load binary file from a filesystem image
go      - start application at address 'addr'
help    - print online help
iminfo  - print header information for application image
imls    - list all images found in flash
itest    - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loop    - infinite loop on address range
ls    - list files in a directory (default /)
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nfs    - boot image via network using NFS protocol
nm      - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sleep   - delay execution for some time
tftpboot- boot image via network using TFTP protocol
version - print monitor version
EDB9312> tftpboot
*** ERROR: `serverip' not set
EDB9312> server
help
?       - alias for 'help'
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp    - boot image via network using BootP/TFTP protocol
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
echo    - echo args to console
erase   - erase FLASH memory
flinfo  - print FLASH memory information
fsinfo    - print information about filesystems
fsload    - load binary file from a filesystem image
go      - start application at address 'addr'
help    - print online help
iminfo  - print header information for application image
imls    - list all images found in flash
itest    - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loop    - infinite loop on address range
ls    - list files in a directory (default /)
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nfs    - boot image via network using NFS protocol
nm      - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sleep   - delay execution for some time
tftpboot- boot image via network using TFTP protocol
version - print monitor version
EDB9312> d
bdinfo
arch_number = 0x000001C3
env_t       = 0x00000000
boot_params = 0xC0000100
DRAM bank   = 0x00000000
-> start    = 0xC0000000
-> size     = 0x02000000
ethaddr     = 08:00:3E:26:0A:5B
ip_addr     = 0.0.0.0
baudrate    = 115200 bps
EDB9312> flinfo
Bank # 1: Intel: 28F128J3 (128Mbit)
  Size: 4 MB in 128 Sectors
  Sector Start Addresses:
    00000000      00020000      00040000      00060000      00080000     
    000A0000      000C0000      000E0000      00100000      00120000     
    00140000      00160000      00180000      001A0000      001C0000     
    001E0000      00200000      00220000      00240000      00260000     
    00280000      002A0000      002C0000      002E0000      00300000     
    00320000      00340000      00360000      00380000      003A0000     
    003C0000      003E0000      00400000      00420000      00440000     
    00460000      00480000      004A0000      004C0000      004E0000     
    00500000      00520000      00540000      00560000      00580000     
    005A0000      005C0000      005E0000      00600000      00620000     
    00640000      00660000      00680000      006A0000      006C0000     
    006E0000      00700000      00720000      00740000      00760000     
    00780000      007A0000      007C0000      007E0000      00800000     
    00820000      00840000      00860000      00880000      008A0000     
    008C0000      008E0000      00900000      00920000      00940000     
    00960000      00980000      009A0000      009C0000      009E0000     
    00A00000      00A20000      00A40000      00A60000      00A80000     
    00AA0000      00AC0000      00AE0000      00B00000      00B20000     
    00B40000      00B60000      00B80000      00BA0000      00BC0000     
    00BE0000      00C00000      00C20000      00C40000      00C60000     
    00C80000      00CA0000      00CC0000      00CE0000      00D00000     
    00D20000      00D40000      00D60000      00D80000      00DA0000     
    00DC0000      00DE0000      00E00000      00E20000      00E40000     
    00E60000      00E80000      00EA0000      00EC0000      00EE0000     
    00F00000      00F20000      00F40000      00F60000      00F80000     
    00FA0000      00FC0000      00FE0000     
EDB9312> coninfo
List of available devices:
serial   80000003 SIO stdin stdout stderr 
EDB9312> ls
Scanning JFFS2 FS:   
 done.
EDB9312> md
Usage:
md      - memory display
EDB9312> printenv
bootargs=root=1f02 console=ttyAM0 mtdparts=phys_mapped_flash:128k(Uboot)ro,1024k(kernel)ro,1024k(cramfs)ro,-(jffs2)
bootcmd=bootm 0x20000
bootdelay=1
baudrate=115200
ethaddr=08:00:3e:26:0a:5b
stdin=serial
stdout=serial
stderr=serial
Environment size: 233/262140 bytes
EDB9312> version
U-Boot 1.1.2 (Jun  7 2005 - 09:16:44)
EDB9312> iminfo
## Checking Image at 01000000 ...
   Bad Magic Number
EDB9312> boot
## Booting image at 00020000 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    718308 Bytes = 701.5 kB
   Load Address: c0008000
   Entry Point:  c0008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.4.27-vrs1-crus142 (mp7000@DevptMP7000) (gcc version 3.3) #5 ven jun 2 12:22:16 CEST 2006
CPU: Arm920Tid(wb) revision 0
Machine: edb9312
Examining tag list @0xc0000100 ...Ok.
parsing command line... ok.
bootmem_init... ok.
paging_init... On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
requesting resources... ok.
Kernel command line: root=1f02 console=ttyAM0 mtdparts=phys_mapped_flash:128k(Uboot)ro,1024k(kernel)ro,1024k(cramfs)ro,-(jffs2)
Calibrating delay loop... 99.35 BogoMIPS
Before waiting loop for hard drive
After waiting loop for hard drive
Memory: 32MB = 32MB total
Memory: 30676KB available (1311K code, 340K data, 44K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
CPU: Testing write buffer: pass
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
GPIO port C initialised 
GPIO port B initialised 
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
ttyAM0 at MMIO 0xff8c0000 (irq = 52) is a AMBA
ttyAM1 at MMIO 0xff8d0000 (irq = 54) is a AMBA
ttyAM2 at MMIO 0xff8e0000 (irq = 55) is a AMBA
pty: 256 Unix98 ptys configured
ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic
Dma memory allocated : 1164 @ 0xc287e000
ep93xx_ethernet #0 at 0xff010000 IRQ:39 MAC:00:ba:d0:0b:ad:00
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive
hdb: Maxtor 6L080P0, ATA DISK drive
ide0 at 0x800-0x807,0x406 on irq 40
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 160086528 sectors (81964 MB) w/8192KiB Cache, CHS=158816/16/63, UDMA 2 
hda: attached ide-cdrom driver.
hda: ATAPI 40X DVD-ROM drive, 254kB Cache, UDMA 2 
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hdb: hdb1 hdb2
SCSI subsystem driver Revision: 1.00
EDB9312-NOR:0x00800000 at 0x00000000
Unknown command : 0xff
Unknown command : 0xff
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
NOR flash on EDB9312: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
mtd: Giving out device 0 to NOR flash on EDB9312
EDB9312-NOR:using edb9312 partition definition
Creating 3 MTD partitions on "NOR flash on EDB9312":
0x00000000-0x00120000 : "zImage"
mtd: Giving out device 1 to zImage
0x00120000-0x00220000 : "CRAMFS"
mtd: Giving out device 2 to CRAMFS
0x00220000-0x007e0000 : "JFFS2"
mtd: Giving out device 3 to JFFS2
EDB9312-NOR:no partition info available
i2c-core.o: i2c core module version 2.6.1 (20010830)
Initialising first I2C bus
Initialising second I2C bus
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xff020000, IRQ 56
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 44K
init started:  BusyBox v1.00 (2006.06.14-15:05+0000) multi-call binary
Using /modules/mood_screen.o