IMX233 Olinuxino Micro

About

Olimex is selling a cheap linux board based on the Freescale IMX233 SoC.

iMX233-OLinuXino-Micro-1.jpg

Specifications

  • iMX233 454Mhz ARM9 processor
  • 64MB RAM
  • SD-card reader
  • TV PAL/NTSC video output
  • one USB High-Speed host port
  • 60 GPIO pins

Notes

I had to pay via Paypal because their webpage form was a bit broken, since it was requiring frames. I went on IRC, and people recommend me to order via Paypal. It would be better if Olimex invests into a trusted payment broker, which is not the case right now. For another order of some Atmega43u4 boards, Olimex even asked me to send my credit card number via email.

Serial messages

On the serial console, I got the following error messages:

0x8020a01d
0x8020a01d
0x8020a01d
0x8020a01d
0x8020a01d
0x8020a01d
0x80502008
0x8020a01d
0x80502008
0x8020a01d
0x80502008
0x8020a01d
0x80502008
0x8020a01d
0x80502008
0x8020a01d

According to the Error codes document for the IMX233:

0x8020a01d: ERROR_DDI_SD_DRIVER_GROUP
0x80502008: ERROR_ROM_USB_DRIVER_GROUP

It seems the bootloader cannot boot over the SD card nor the USB drive. Maybe the partition table was wrongly made.

Without an SD card it says:

0x80502008
          0x8020a01d
0x8020a014
0x8020a014
0x8020a014
0x80502008
          0x8020a014
0x80502008
          0x8020a014
0x80502008
          0x8020a014

Serial output

HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFC
PowerPrep start initialize power...
Battery Voltage = 0.65V
No battery or bad battery                    detected!!!.Disabling battery                    voltage measurements./r/nLLCMay 11 201215:26:EMI_CTRL 0x1C08404init_ddr_mt46v32m10Frac 0x92926192
start change cpu fr
LLLLLLLFCLJUncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3_OLinuXinoR4 (hehopmajieh@hehopmajieh-office) (gcc version 4.7.1 20120421 (prerelease) (GCC) ) #11 PREEMPT Mon May 21 10:27:52 EEST 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: iMX233-OLinuXino low cost board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd console=ttyAM0,115200 root=/dev/mmcblk0p2 rw rootwait ssp1=mmc
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 57208k/57208k available, 8328k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)
    vmalloc : 0xc4800000 - 0xf0000000   ( 696 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0026000   ( 120 kB)
      .text : 0xc0026000 - 0xc033d000   (3164 kB)
      .data : 0xc0356000 - 0xc0381a00   ( 175 kB)
Hierarchical RCU implementation.
    RCU-based detection of stalled CPUs is disabled.
    Verbose stalled-CPUs detection is disabled.
NR_IRQS:224
Console: colour dummy device 80x30
console [ttyAM0] enabled
Calibrating delay loop... 226.91 BogoMIPS (lpj=1134592)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normal 
regulator: vdddbo: 800 <--> 1575 mV fast normal 
regulator: vdda: 1500 <--> 2275 mV at 1750 mV fast normal 
regulator: vddio: 2800 <--> 3575 mV at 3300 mV fast normal 
regulator: overall_current: fast normal 
regulator: mxs-duart-1: fast normal 
regulator: mxs-bl-1: fast normal 
regulator: mxs-i2c-1: fast normal 
regulator: mmc_ssp-1: fast normal 
regulator: mmc_ssp-2: fast normal 
regulator: charger-1: fast normal 
regulator: power-test-1: fast normal 
regulator: cpufreq-1: fast normal 
i.MX IRAM pool: 28 KB@0xc4808000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Freeing initrd memory: 4096K
Bus freq driver module loaded
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
msgmni has been set to 119
alg: No test for stdrng (krng)
cryptodev: driver loaded.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 80x30
mxs-duart.0: ttyAM0 at MMIO 0x80070000 (irq = 0) is a DebugUART
brd: module loaded
loop: module loaded
usbcore: registered new interface driver smsc95xx
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci: irq 11, io base 0x80080000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.3_OLinuXinoR4 ehci_hcd
usb usb1: SerialNumber: fsl-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
MXS RTC driver v1.0 hardware v2.0.0
mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as rtc0
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
mxs watchdog: initialized, heartbeat 19 sec
mxs-mmc: MXS SSP Controller MMC Interface driver
ssp_set_rate: error -110
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 14 ERRIRQ 15 
dcp dcp.0: DCP crypto enabled.!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mxs-adc-audio mxs-adc-audio.0: MXS ADC/DAC Audio Codec 
No device for DAI mxs adc/dac
No device for DAI mxs adc/dac
asoc: mxs adc/dac <-> mxs adc/dac mapping ok
ALSA device list:
  #0: MXS EVK (mxs adc/dac)
TCP cubic registered
NET: Registered protocol family 17
mxs-rtc mxs-rtc.0: setting system clock to 1970-01-01 00:00:10 UTC (10)
Waiting for root device /dev/mmcblk0p2...
mmc0: new high speed SD card at address 0007
mmcblk0: mmc0:0007 SD02G 1.83 GiB 
 mmcblk0: p1 p2
EXT2-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 179:2.
Freeing init memory: 120K
INIT: 
version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...udevd-work[418]: error opening ATTR{/sys/class/sound/controlC0/../uevent} for writing: No such file or directory
done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
Checking root file system...fsck from util-linux-ng 2.17.2
/lib/init/rw/rootdev was not cleanly unmounted, check forced.
/lib/init/rw/rootdev: |==                                      |  4.7%   
/lib/init/rw/rootdev: |====                                    /  9.3%   
/lib/init/rw/rootdev: |======                                  - 14.0%   
/lib/init/rw/rootdev: |=======                                 \ 18.7%   
/lib/init/rw/rootdev: |=========                               | 23.3%   
/lib/init/rw/rootdev: |===========                             / 28.0%   
/lib/init/rw/rootdev: |=============                           - 32.7%   
/lib/init/rw/rootdev: |===============                         \ 37.3%   
/lib/init/rw/rootdev: |=================                       | 42.0%   
/lib/init/rw/rootdev: |===================                     / 46.7%   
/lib/init/rw/rootdev: |=====================                   - 51.3%   
/lib/init/rw/rootdev: |======================                  \ 56.0%   
/lib/init/rw/rootdev: |========================                | 60.7%   
/lib/init/rw/rootdev: |==========================              / 65.3%   
/lib/init/rw/rootdev: |============================            - 70.0%   
/lib/init/rw/rootdev: |============================            \ 70.2%   
/lib/init/rw/rootdev: |============================            | 71.1%   
/lib/init/rw/rootdev: |=============================           / 72.4%   
/lib/init/rw/rootdev: |=============================           - 73.6%   
/lib/init/rw/rootdev: |==============================          \ 74.6%   
/lib/init/rw/rootdev: |==============================          | 75.7%   
/lib/init/rw/rootdev: |===============================         / 76.5%   
/lib/init/rw/rootdev: |===============================         - 77.5%   
/lib/init/rw/rootdev: |===============================         \ 78.4%   
/lib/init/rw/rootdev: |================================        | 79.5%   
/lib/init/rw/rootdev: |================================        / 80.5%   
/lib/init/rw/rootdev: |=================================       - 82.0%   
/lib/init/rw/rootdev: |=================================       \ 82.8%   
/lib/init/rw/rootdev: |==================================      | 83.8%   
/lib/init/rw/rootdev: |==================================      / 84.9%   
/lib/init/rw/rootdev: |==================================      - 86.1%   
/lib/init/rw/rootdev: |===================================     \ 87.3%   
/lib/init/rw/rootdev: |===================================     | 88.3%   
/lib/init/rw/rootdev: |====================================    / 89.6%   
Rebuilding directory: |===========                     - 33.3%  49871
/lib/init/rw/rootdev: |=====================================   \ 93.6%   
/lib/init/rw/rootdev: |======================================  | 95.8%   
/lib/init/rw/rootdev: |======================================= / 96.8%   
/lib/init/rw/rootdev: |========================================- 99.5%   
/lib/init/rw/rootdev: |========================================| 100.0%   

/lib/init/rw/rootdev: ***** REBOOT LINUX *****
/lib/init/rw/rootdev: 10097/119040 files (0.2% non-contiguous), 80422/475904 blocks
fsck died with exit status 3
[31mfailed (code 3).
[39;49m
The file system check corrected errors on the root partition but requested that the system be restarted. ... 
[31mfailed!
[39;49m
The system will be restarted in 5 seconds. ... 
[33m(warning).
[39;49m
Restarting system.
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFC
PowerPrep start initialize power...
Battery Voltage = 2.14V
No battery or bad battery                    detected!!!.Disabling battery                    voltage measurements./r/nLLCMay 11 201215:26:EMI_CTRL 0x1C08404init_ddr_mt46v32m10Frac 0x92926192
start change cpu fr
LLLLLLLFCLJUncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3_OLinuXinoR4 (hehopmajieh@hehopmajieh-office) (gcc version 4.7.1 20120421 (prerelease) (GCC) ) #11 PREEMPT Mon May 21 10:27:52 EEST 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: iMX233-OLinuXino low cost board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd console=ttyAM0,115200 root=/dev/mmcblk0p2 rw rootwait ssp1=mmc
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 57208k/57208k available, 8328k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)
    vmalloc : 0xc4800000 - 0xf0000000   ( 696 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0026000   ( 120 kB)
      .text : 0xc0026000 - 0xc033d000   (3164 kB)
      .data : 0xc0356000 - 0xc0381a00   ( 175 kB)
Hierarchical RCU implementation.
    RCU-based detection of stalled CPUs is disabled.
    Verbose stalled-CPUs detection is disabled.
NR_IRQS:224
Console: colour dummy device 80x30
console [ttyAM0] enabled
Calibrating delay loop... 226.91 BogoMIPS (lpj=1134592)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normal 
regulator: vdddbo: 800 <--> 1575 mV fast normal 
regulator: vdda: 1500 <--> 2275 mV at 1750 mV fast normal 
regulator: vddio: 2800 <--> 3575 mV at 3300 mV fast normal 
regulator: overall_current: fast normal 
regulator: mxs-duart-1: fast normal 
regulator: mxs-bl-1: fast normal 
regulator: mxs-i2c-1: fast normal 
regulator: mmc_ssp-1: fast normal 
regulator: mmc_ssp-2: fast normal 
regulator: charger-1: fast normal 
regulator: power-test-1: fast normal 
regulator: cpufreq-1: fast normal 
i.MX IRAM pool: 28 KB@0xc4808000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Freeing initrd memory: 4096K
Bus freq driver module loaded
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
msgmni has been set to 119
alg: No test for stdrng (krng)
cryptodev: driver loaded.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 80x30
mxs-duart.0: ttyAM0 at MMIO 0x80070000 (irq = 0) is a DebugUART
brd: module loaded
loop: module loaded
usbcore: registered new interface driver smsc95xx
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci: irq 11, io base 0x80080000
fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.35.3_OLinuXinoR4 ehci_hcd
usb usb1: SerialNumber: fsl-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
MXS RTC driver v1.0 hardware v2.0.0
mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as rtc0
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
mxs watchdog: initialized, heartbeat 19 sec
mxs-mmc: MXS SSP Controller MMC Interface driver
ssp_set_rate: error -110
mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 14 ERRIRQ 15 
dcp dcp.0: DCP crypto enabled.!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mxs-adc-audio mxs-adc-audio.0: MXS ADC/DAC Audio Codec 
No device for DAI mxs adc/dac
No device for DAI mxs adc/dac
asoc: mxs adc/dac <-> mxs adc/dac mapping ok
ALSA device list:
  #0: MXS EVK (mxs adc/dac)
TCP cubic registered
NET: Registered protocol family 17
mxs-rtc mxs-rtc.0: setting system clock to 1970-01-01 00:00:57 UTC (57)
Waiting for root device /dev/mmcblk0p2...
mmc0: new high speed SD card at address 0007
mmcblk0: mmc0:0007 SD02G 1.83 GiB 
 mmcblk0: p1 p2
VFS: Mounted root (ext2 filesystem) on device 179:2.
Freeing init memory: 120K
INIT: 
version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...udevd-work[423]: error opening ATTR{/sys/class/sound/controlC0/../uevent} for writing: No such file or directory
done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
Checking root file system...fsck from util-linux-ng 2.17.2
/lib/init/rw/rootdev: clean, 10097/119040 files, 80422/475904 blocks
done.
Cleaning up ifupdown....
Setting up networking....
Loading kernel modules...done.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...cat: /sys/class/net/usb0/address: No such file or directory
run-parts: /etc/network/if-pre-up.d/00-persistent-mac exited with return code 1
cat: /sys/class/net/usb0/address: No such file or directory
run-parts: /etc/network/if-pre-up.d/00-persistent-mac exited with return code 1a
SIOCSIFHWADDR: No such device
Failed to bring up usb0.
done.
Cleaning up temporary files....
Setting kernel variables ...done.
INIT: 
Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Debian GNU/Linux 6.0 debian ttyAM0
debian login:

GPIO

Some GPIOs are already exposed in /sys/class/gpio:

root@debian:/sys/class/gpio# ls -al
total 0
drwxr-xr-x 30 root root    0 Jan  1 02:00 .
drwxr-xr-x 23 root root    0 Jan  1 02:00 ..
--w-------  1 root root 4096 Jan  1 02:00 export
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio0
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio1
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio16
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio17
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio19
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio2
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio20
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio23
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio24
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio25
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio3
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio30
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio31
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio4
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio5
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio51
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio52
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio53
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio55
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio56
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio6
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio65
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio7
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio91
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpio92
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpiochip0
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpiochip32
drwxr-xr-x  3 root root    0 Jan  1 02:00 gpiochip64
--w-------  1 root root 4096 Jan  1 02:00 unexport
root@debian:/sys/class/gpio#

Cpuinfo

root@debian:~# cat /proc/cpuinfo 
Processor       : ARM926EJ-S rev 5 (v5l)
BogoMIPS        : 226.91
Features        : swp half thumb fastmult edsp java 
CPU implementer : 0x41
CPU architecture: 5TEJ
CPU variant     : 0x0
CPU part        : 0x926
CPU revision    : 5

Hardware        : iMX233-OLinuXino low cost board
Revision        : 0000
Serial          : 0000000000000000

Problems

The debian kernel provided does not have any modules. For example, I plugged in some ethernet over USB card (asix module) which is missing.

Similar devices

Chumby One

It seems the Chumby One is also based on the IMX233, has the same amount of RAM.

Philips VP5500

It is also based on some IMX processor, not sure if it is the same SoC.

Links