Belgacom Box 3 (Bbox3) by Technicolor

About

Belgacom Box 3 (Bbox3) by Technicolor.

This seems to be the most deploied one, there is also the Bbox3 by Sagemcom, but this later model is not as widespread as the one by Technicolor.

Ideas

The flash on the board is an SPI one with 8 pins, it should be fairly easy to dump the content of it, for example with a bus pirate and flashrom.

Toolchain openwrt support

There are some new patches for the ARC arch in openwrt trunk.

Serial port

There is a serial port on the side of the SoC, where you have to bridge 2 sides with a bit of solder in order to make the contact.

See the picture here:

bbox3-technicolor-serial-port-1.jpg

Here I took the ground with the green wire:

bbox3-technicolor-serial-port-2.jpg

Here if you zoom, you should notice that I had to bridge 2 pins on the PCB:

bbox3-technicolor-serial-port-3.jpg

Here is the full serial log:

Quantenna Mini U-Boot
Version: 1.4.6 Built: Oct 08 2012 at 18:12:00
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
reset command
Quantenna Mini U-Boot
Version: 1.4.6 Built: Oct 08 2012 at 18:12:00
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
reset command
Quantenna Mini U-Boot
Version: 1.4.6 Built: Oct 08 2012 at 18:12:00
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T T T T 
Retry count exceeded; starting again
reset command
Quantenna Mini U-Boot
Version: 1.4.6 Built: Oct 08 2012 at 18:12:00
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-uboot'.
Load address: 0x88000000
Loading: *
T #########
done
Bytes transferred = 127992 (1f3f8 hex)
Boot reached stage 81
Boot reached stage 84
Info: data uncached: addr=0xc0000000 size=1024MB
Info: text at 0x88000000, stack at 0x8803e7fc(8192), heap at 0x88030000(51200), uboot size 155352
Info: i-cache is enabled
Info: d-cache is enabled
Info: CPU freq is 400000000, dev freq is 125000000
Info: Quantenna U-Boot version:1.4.10
Info: TCH bootloader version:10.5.2.O
Info: build date 'Mar 05 2014', time '12:46:33'
spi clock: val=0x3 ctl=0x80298002
spi clock: val=0x0 ctl=0x80280002
SPI flash info:
    name             : mx25l512e
    jedec_id         : 0xc22010
    sector size      : 4096
    number of sector : 16
    frequency        : 104000000
    flags            : 0x2
    lock             : 
Boot reached stage 13
Boot reached stage 12
env size = 0x3ffc
Valid CRC found in flash restoring env...
Boot reached stage 11
board config:etron16-160, emac1 b2b-rgmii 1000M, pa2
BDA at 0x80002000
In:    serial
Out:   serial
Err:   serial
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Hit any key to stop autoboot:  0 
post_mask is null
Boot reached stage 80
1G-FD
Using QTN-EMAC device
L2_TFTP start
Filename 'qtn-linux.lzma'.
Load address: 0x82000000
Loading: *
#################################################################
     #################################################################
     #################################################################
     ##########################################################
done
Bytes transferred = 3692118 (385656 hex)
Boot reached stage 81
Boot reached stage 84
Boot reached stage 1
## Booting kernel from Legacy Image at 82000000 ...
Boot reached stage 2
Boot reached stage 3
   Image Name:   ruby-linux
   Image Type:   arc Linux Kernel Image (lzma compressed)
   Data Size:    3683926 Bytes =  3.5 MB
   Load Address: 80302000
   Entry Point:  80302000
   Verifying Checksum ... OK
Boot reached stage 4
Boot reached stage 5
Boot reached stage 6
Boot reached stage 14
   Uncompressing Kernel Image ... OK
Boot reached stage 7
Boot reached stage 8
Command line TAG setup
Params->u.cmdline.cmdline earlyprintk=1 console=ttyS0,115200n8 mtdparts=spi_flash:20k(uboot),16k(uboot_env),-(data) hw_config_id=8001
p earlyprintk=1 console=ttyS0,115200n8 mtdparts=spi_flash:20k(uboot),16k(uboot_env),-(data) hw_config_id=8001
## Transferring control to Linux (at address 80302000) ATAG parameters 880340a0 - 8803412c...
[    0.000000] Linux version 2.6.30 (buildmgm@edgmwbuild226.edegem.eu.thmulti.com) (gcc version 4.2.1 (ARC_2.3)) #2 Wed Mar 5 12:57:24 CET 2014
[    0.000000] Parsing ATAG parameters from bootloader
[    0.000000] ATAG_CORE: successful parsing
[    0.000000] ATAG_CMDLINE: command line = earlyprintk=1 console=ttyS0,115200n8 mtdparts=spi_flash:20k(uboot),16k(uboot_env),-(data) hw_config_id=8001
[    0.000000] Board id: 8001
[    0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 8001
[    0.000000] 
[    0.000000]  Processor Family: ARC 700, Core ID: 0
[    0.000000] CPU speed :    400.00 Mhz
[    0.000000] Timers:     TIMER1 TIMER0 
[    0.000000] Interrupt Vect Base:     0x88010800 
[    0.000000] Peripheral Base:     0x0 
[    0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB 
[    0.000000] ARC700 MMU Ver [2]
[    0.000000]    uDTLB 8 entr, uITLB 4 entr, JTLB 128 entry/way, 2 ways
[    0.000000] TLB Refill "will NOT" Flush uTLBs
[    0.000000] Detected I-cache : 
[    0.000000]   Type=2 way set-assoc, Line length=32, Size=16K (enabled)
[    0.000000] Detected D-cache : 
[    0.000000]   Type=4 way set-assoc, Line length=32, Size=16K (enabled)
[    0.000000] Extensions:
[    0.000000] Multiplier: 32x32 with ANY Result Reg   MAC Multiplier: Dual 16 x 16 and 32 x 16
[    0.000000] CRC  Instrn: NA,   SWAP Instrn: Present   NORM Instrn: Present
[    0.000000] Min-Max Instrn: Present,   Barrel Shift Rotate Instrn: Present
[    0.000000] Ext Arith Instrn: Present
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 80d581c0, node_mem_map 81000000
[    0.000000]   Normal zone: 36 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8156 pages, LIFO batch:0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8156
[    0.000000] Kernel command line: earlyprintk=1 console=ttyS0,115200n8 mtdparts=spi_flash:20k(uboot),16k(uboot_env),-(data) hw_config_id=8001
[    0.000000] console [ruby_early0] enabled
[    0.000000] RCU-based detection of stalled CPUs is enabled.
[    0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[    0.000000] clockevent mode switch to [1]
[    0.000000] clockevent mode switch to [2]
[    0.000000] Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
[    0.005000] Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
[    0.020000] Memory: 51600KB available (2051K code,560K data, 8080K init)
[    0.025000] Calibrating delay loop... 265.42 BogoMIPS (lpj=663552)
[    0.145000] Mount-cache hash table entries: 1024
[    0.155000] Starting ksoftirqd, stack (thread_info) at 88002000 cpu 0
[    0.160000] net_namespace: 932 bytes
[    0.165000] NET: Registered protocol family 16
[    0.170000] Ruby heap in SRAM from 88010000 to 8801ffe0
[    0.175000] Quantenna I2C device register
[    0.185000] bio: create slab <bio-0> at 0
[    0.195000] NET: Registered protocol family 2
[    0.200000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
[    0.210000] TCP established hash table entries: 2048 (order: 1, 16384 bytes)
[    0.215000] TCP bind hash table entries: 2048 (order: 0, 8192 bytes)
[    0.220000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.225000] TCP reno registered
[    0.230000] NET: Registered protocol family 1
[    0.760000] JFFS2 version 2.2. (NAND) 
 2001-2006 Red Hat, Inc.
[    0.765000] msgmni has been set to 100
[    0.770000] io scheduler noop registered (default)
[    0.775000] io scheduler anticipatory registered
[    1.325000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    1.335000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A
[    1.345000] console handover: boot [ruby_early0] -> real [ttyS0]
[    1.350000] brd: module loaded
[    1.360000] loop: module loaded
[    1.365000] 3 cmdlinepart partitions found on MTD device spi_flash
[    1.370000] Creating 3 MTD partitions on "spi_flash":
[    1.375000] 0x000000000000-0x000000005000 : "uboot"
[    1.385000] 0x000000005000-0x000000009000 : "uboot_env"
[    1.390000] 0x000000009000-0x000000010000 : "data"
[    1.400000] spi_flash: SPI flash driver initialized successfully!
[    1.405000] ruby_health loading
[    1.410000] emac_eth version 1.0 Quantenna Communications, Inc.
[    1.415000] emac_eth version 1.0 Quantenna Communications, Inc.
[    1.420000] Random stuff 87
[    1.555000] eth1_emac1: Arasan Ethernet found at 0xe8000000, irq 20
[    1.560000] u32 classifier
[    1.565000]     input device check on 
[    1.570000]     Actions configured 
[    1.570000] Netfilter messages via NETLINK v0.30.
[    1.575000] nf_conntrack version 0.5.0 (988 buckets, 3952 max)
[    1.585000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.590000] TCP cubic registered
[    1.595000] NET: Registered protocol family 10
[    1.600000] NET: Registered protocol family 17
[    1.605000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.610000] All bugs added by David S. Miller <davem@redhat.com>
[    1.620000] Freeing unused kernel memory: 8080k freed [80302000] TO [80ae6000]
init started: BusyBox v1.10.3 (2014-03-05 12:47:20 CET)
starting pid 32, tty '': '/etc/init.d/rcS'
Initializing random number generator... done.
[    2.525000] eth1_emac1: force link (1000/Full)
Downloading qtn_prod.env (1).
Failed to download qtn_prod.env ( tftp error : Access Violation )
Downloading qtn_prod.env (2).
Downloading qtn_custo.env (1).
Downloading qtn_custo.sh (1).
Updating eth_macaddr
Updating wifi_mac_addrs
Updating wireless_conf.txt
Updating hostapd.conf
Updating tch_upgrade.conf
Updating tch_ntp.conf
Updating tch_monitor.conf
Updating admin.conf
Updating tch_cwmp_conf
Starting network...
emac0 is unused, emac1 is eth1_0
/sbin/ifup -a
[    5.890000] eth1_0: force link (1000/Full)
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
[    6.285000] eth1_0: force link (1000/Full)
[    6.450000] device eth1_0 entered promiscuous mode
[    6.480000] br0: port 1(eth1_0) entering forwarding state
Starting wireless...
Loading modules
[    7.685000] qtn_debug: module license 'Proprietary' taints kernel.
[    7.690000] Disabling lock debugging due to kernel taint
modprobe: module i2cbus not found
modprobe: failed to load module i2cbus
modprobe: module qtsens not found
modprobe: failed to load module qtsens
[    7.950000] wlan using SRAM (offset:0x880100d8, size:0x688)
[    8.165000] wlan: 0.8.4.2 (0.9.3.3)
[    8.285000] qvspmod using SRAM (offset:0x88010768, size:0x1eb4)
[    8.385000] qdrv using SRAM (offset:0x88012628, size:0xb2c4)
Production mode
Waiting for Wireless Events from interfaces...
[    9.450000]  qdrv: firmware: requesting rdsp_driver.0.bin
[    9.550000]  qdrv: firmware: requesting qtn_driver.qtn_ruby.0.bin
[   10.480000] muc_print_init_shared: buf=550e1560
[   10.485000] MuC: build date=Thu Nov 14 22:31:48 PST 2013
[   10.490000] MuC: slow heap begin=0x000c5500 end=0x00145500
[   10.495000] MuC: fast heap begin=0x80030800 end=0x80038800
[   10.500000] MuC: stack start=0x8003e7a0 sp=0x8003ff04
[   10.505000] MuC: calstate is 3 (prod), dcache on
[   10.510000] MuC: scancnt=0
[   10.515000] MuC: slow eth=0
[   10.530000] MuC: POST RF loopback test is disabled
[   10.650000] MuC: fd start=0xe5040300 count=48 size=100 end=0xe50415c0
[   10.655000] MuC: TX QoS schedule=0
[   10.655000] MuC: dynamic one-bit autocorrelation enabled
[   10.660000] MuC: enable IRQs
[   10.690000] QDRV: power adjust scancnt=0
[   10.695000] QDRV: using default temperature profile
[   10.700000] QDRV: could not read temperature sensor
[   10.705000] MuC boot succeeded 0.235 seconds
[   10.920000] VAP create succeeded 0.030 seconds
Set channel 0
[   12.065000] device wifi0 entered promiscuous mode
[   12.240000] Enabling SSDP flooding
SCS BRCM rxif mac a6:b1:e9:b1:ed:ef
SCS using interface wifi0
[   14.315000] WPS: push button is not configured
[   14.325000] br0: port 2(wifi0) entering forwarding state
Enabling beamforming
[   14.940000] qdrv_sch_red: allocated 1536 511
[   14.945000] qdrv_sch_red: attached to wifi0
[   14.975000] qdrv_sch_red: allocated 512 127
[   14.975000] qdrv_sch_red: attached to eth1_0
[   15.165000] Enabling SCS
SCS enabled
[   15.685000] [2]Comparing register set Global control
[   15.710000] [6]Comparing register set BB Global regs
VSP enabled: 0
[   16.435000] qdrv_radar_is_rdetection_required: ERROR - channel not yet set
[   16.440000] MuC: ioctl_power_save, level: 0 -> 1
/scripts/cmdloop starting call_qcsapi, at 00:00:16 up 0 min, load average: 0.59, 0.13, 0.04
/scripts/cmdloop starting /sbin/tch_vb_discover, at 00:00:17 up 0 min, load average: 0.59, 0.13, 0.04
killall: udhcpc: no process killed
[   17.475000] br0: no IPv6 routers present
udhcpc (v1.19.4) started
Sending discover...
tch_monitor.sh: no url defined
BELGACOM CUSTO
[   18.065000] <0,0,2,2,2,3,3,3
[   18.065000] >
starting pid 644, tty '/dev/ttyS0': '/bin/login'
TG233 login: [   18.520000] RADAR: CAC started for channel 132 (5660 MHz)
Sending discover...
Sending discover...
[   24.320000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   24.345000] RADAR: CAC started for channel 132 (5660 MHz)
No lease, forking to background
[   28.615000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   28.620000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.370000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.375000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.385000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.395000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.405000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.415000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.425000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.435000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.445000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.455000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.465000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.475000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.495000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.500000] RADAR: CAC started for channel 132 (5660 MHz)
[   29.535000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   29.545000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.275000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.280000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.290000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.300000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.310000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.320000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.330000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.340000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.350000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.360000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.370000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.375000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.390000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.395000] RADAR: CAC started for channel 132 (5660 MHz)
[   30.425000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   30.435000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.190000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.195000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.205000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.215000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.225000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.235000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.245000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.255000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.265000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.275000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.285000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.290000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.310000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.315000] RADAR: CAC started for channel 132 (5660 MHz)
[   31.345000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   31.355000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.545000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.550000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.555000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.560000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.570000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.580000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.590000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.600000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.610000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.620000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.630000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.640000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.660000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.665000] RADAR: CAC started for channel 132 (5660 MHz)
[   32.695000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   32.705000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.855000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.865000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.870000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.875000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.885000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.895000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.905000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.915000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.925000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.935000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.945000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.955000] RADAR: CAC started for channel 132 (5660 MHz)
[   35.975000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   35.980000] RADAR: CAC started for channel 132 (5660 MHz)
[   36.015000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   36.025000] RADAR: CAC started for channel 132 (5660 MHz)
[   36.935000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   36.945000] RADAR: CAC started for channel 132 (5660 MHz)
[   36.955000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   36.965000] RADAR: CAC started for channel 132 (5660 MHz)
[   36.975000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   36.985000] RADAR: CAC started for channel 132 (5660 MHz)
[   36.995000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   37.005000] RADAR: CAC started for channel 132 (5660 MHz)
[   37.015000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   37.025000] RADAR: CAC started for channel 132 (5660 MHz)
[   37.035000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   37.040000] RADAR: CAC started for channel 132 (5660 MHz)
[   37.060000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   37.065000] RADAR: CAC started for channel 132 (5660 MHz)
[   37.100000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   37.110000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.020000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.030000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.040000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.045000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.050000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.055000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.065000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.075000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.085000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.095000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.105000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.115000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.135000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.140000] RADAR: CAC started for channel 132 (5660 MHz)
[   38.175000] RADAR: CAC stopped for channel 132 (5660 MHz)
[   38.185000] RADAR: CAC started for channel 132 (5660 MHz)
TG233 login: [  108.185000] RADAR: CAC completed for channel 132 (5660 MHz)
[  130.885000] MuC: ioctl_power_save, level: 1 -> 5
TG233 login: user
Password: 
Login incorrect
TG233 login: user
Password: 
Login incorrect
TG233 login: user
Password: 
Login incorrect
starting pid 916, tty '/dev/ttyS0': '/bin/login'
TG233 login: user
Password: 
Login incorrect
TG233 login: user^H^H^H^H^H
Password: 
Login incorrect
TG233 login: root
Password: 
Login incorrect
starting pid 922, tty '/dev/ttyS0': '/bin/login'
TG233 login: admin
Password: 
Login incorrect
TG233 login: admin
Password: 
Login incorrect
TG233 login: admin
Password: 
Login incorrect
starting pid 928, tty '/dev/ttyS0': '/bin/login'
TG233 login: adsm^H^H^H^H
Password: 
adminLogin incorrect
TG233 login: admin
Password: 
Login incorrect
TG233 login: Administray^Htor
Password: 
Login incorrect
starting pid 944, tty '/dev/ttyS0': '/bin/login'
TG233 login: Administrator
Password: 
Login incorrect
TG233 login: Administrator
Password: 
Login incorrect
TG233 login: Administrator
Password: 
Login incorrect
starting pid 970, tty '/dev/ttyS0': '/bin/login'
TG233 login: FE8101EEEC
Password: 
Login incorrect
TG233 login: Administrator
Password: 
Login incorrect
TG233 login: admin
Password: 
Login incorrect
starting pid 981, tty '/dev/ttyS0': '/bin/login'
TG233 login: admin
Password: 
Login incorrect
TG233 login: 
starting pid 982, tty '/dev/ttyS0': '/bin/login'
TG233 login:

Links